Waters Network Systems ProSwitch 2800MR Spezifikationen

12 OPERATING MANUAL ProSwitch 2800M/MR Managed Modular Fiber and Copper Switch Chassis CORPORATE HEADQUATERS MANUFACTURING/CUST

Waters Network Systems 2800M/MR User’s Manual Page 10 3.6 LEDs The following table provides the status and description o

Waters Network Systems 2800M/MR User’s Manual Page 100 Function name: Storm Setting Function description: The bandwidth s

Waters Network Systems 2800M/MR User’s Manual Page 101 5.22 QoS (Quality of Service) Configuration The switch supports t

Waters Network Systems 2800M/MR User’s Manual Page 102 The QoS functions as we mentioned above can be enabled at the same

Waters Network Systems 2800M/MR User’s Manual Page 103 Figure 5.63 – QoS Global Setting Function name: VIP Port Setting

Waters Network Systems 2800M/MR User’s Manual Page 104 Figure 5.64 – VIP Port

Waters Network Systems 2800M/MR User’s Manual Page 105 Function name: 802.1p Setting Function description: This function

Waters Network Systems 2800M/MR User’s Manual Page 106 Function name: D-Type TOS Function description: IP TOS Priority

Waters Network Systems 2800M/MR User’s Manual Page 107 Figure 5.66 – TOS Delay Mapping Function name: T-Type TOS Functi

Waters Network Systems 2800M/MR User’s Manual Page 108 TOS Throughput Priority Mapping: Each Priority can select Queue 0

Waters Network Systems 2800M/MR User’s Manual Page 109 Parameter description: TOS Reliability Priority Mapping: Each Pri

Waters Network Systems 2800M/MR User’s Manual Page 11 3.7 Rear Panel Located on the rear panel is the RS-232 DB-9 interf

Waters Network Systems 2800M/MR User’s Manual Page 110 Function name: M-Type TOS Function description: IP TOS Priority af

Waters Network Systems 2800M/MR User’s Manual Page 111 Function name: DSCP Setting Function description: In the late 1990

Waters Network Systems 2800M/MR User’s Manual Page 112 5.23 Diagnostics Three functions, including Diagnostics, Loopb

Waters Network Systems 2800M/MR User’s Manual Page 113 link partner. If the switch is not connected to active network dev

Waters Network Systems 2800M/MR User’s Manual Page 114 Figure 5.73 - Ping Test 5.24 TFTP Server Function

Waters Network Systems 2800M/MR User’s Manual Page 115 5.25 Log This function displays the log data. The switch provide

Waters Network Systems 2800M/MR User’s Manual Page 116 5.26 Firmware Upgrade A software upgrade tool is used to upgrade

Waters Network Systems 2800M/MR User’s Manual Page 117 5.27 Reboot There are a few ways to reboot the switch, includin

Waters Network Systems 2800M/MR User’s Manual Page 118 5.28 Logout You can manually logout by using Logout function. Yo

Waters Network Systems 2800M/MR User’s Manual Page 119 6.0 Operation of CLI Management Section 4 of this manual provid

Waters Network Systems 2800M/MR User’s Manual Page 12 3.11.1 Cabling Requirements for SFP Module The GSM2800M has four

Waters Network Systems 2800M/MR User’s Manual Page 120 6.2 Commands of CLI To see the commands of the mode, please input

Waters Network Systems 2800M/MR User’s Manual Page 121 The following table lists the CLI commands and descriptions. Comm

Waters Network Systems 2800M/MR User’s Manual Page 122 Command Syntax Description Argument Possible Value order to use th

Waters Network Systems 2800M/MR User’s Manual Page 123 Command Syntax Description Argument Possible Value becomes unautho

Waters Network Systems 2800M/MR User’s Manual Page 124 Command Syntax Description Argument Possible Value Show state Show

Waters Network Systems 2800M/MR User’s Manual Page 125 Command Syntax Description Argument Possible Value syntax 1, 5-7 S

Waters Network Systems 2800M/MR User’s Manual Page 126 Command Syntax Description Argument Possible Value <data_rate&g

Waters Network Systems 2800M/MR User’s Manual Page 127 Command Syntax Description Argument Possible Value GVRP Disable di

Waters Network Systems 2800M/MR User’s Manual Page 128 Command Syntax Description Argument Possible Value Show config sho

Waters Network Systems 2800M/MR User’s Manual Page 129 Command Syntax Description Argument Possible Value tffp. Mac-Table

Waters Network Systems 2800M/MR User’s Manual Page 13 the Level 1 switch. This generally applies if no VLAN or other spe

Waters Network Systems 2800M/MR User’s Manual Page 130 Command Syntax Description Argument Possible Value 4094 <queue&

Waters Network Systems 2800M/MR User’s Manual Page 131 Command Syntax Description Argument Possible Value [<action>

Waters Network Systems 2800M/MR User’s Manual Page 132 Command Syntax Description Argument Possible Value information (in

Waters Network Systems 2800M/MR User’s Manual Page 133 Command Syntax Description Argument Possible Value Enable QOS enab

Waters Network Systems 2800M/MR User’s Manual Page 134 Command Syntax Description Argument Possible Value (24) <class&

Waters Network Systems 2800M/MR User’s Manual Page 135 Command Syntax Description Argument Possible Value You don't

Waters Network Systems 2800M/MR User’s Manual Page 136 Command Syntax Description Argument Possible Value Set set <ing

Waters Network Systems 2800M/MR User’s Manual Page 137 Command Syntax Description Argument Possible Value delay -1)>=M

Waters Network Systems 2800M/MR User’s Manual Page 138 Command Syntax Description Argument Possible Value start Day (01-3

Waters Network Systems 2800M/MR User’s Manual Page 139 Command Syntax Description Argument Possible Value active: set the

Waters Network Systems 2800M/MR User’s Manual Page 14 3. The switch manager has to assign different names for each VLAN g

Waters Network Systems 2800M/MR User’s Manual Page 140 Command Syntax Description Argument Possible Value <default_pri

Waters Network Systems 2800M/MR User’s Manual Page 141 Command Syntax Description Argument Possible Value VS Disable disa

Waters Network Systems 2800M/MR User’s Manual Page 142 7.0 Maintenance  The possible causes for a no link LED status

Waters Network Systems 2800M/MR User’s Manual Page 143 8.0 Troubleshooting All Waters’ switching products are designed

Waters Network Systems 2800M/MR User’s Manual Page 144 4. A record of changes that have been made to your network config

Waters Network Systems 2800M/MR User’s Manual Page 145 9.0 Warranty Waters Network Systems’ Warranty Statement Waters

Waters Network Systems 2800M/MR User’s Manual Page 15 4.0 Access to Management Functions There are three ways to acce

Waters Network Systems 2800M/MR User’s Manual Page 16 4.2 Configuring IP, Subnet Mask and Default Gateway The default s

Waters Network Systems 2800M/MR User’s Manual Page 17 Before you are able to communicate with the switch, you must know

Waters Network Systems 2800M/MR User’s Manual Page 18 network identifier identifies the network on which the host resides

Waters Network Systems 2800M/MR User’s Manual Page 19 Class C: IP address range between 192.0.0.0 and 223.255.255.255.

Waters Network Systems 2800M/MR User’s Manual Page 2 TABLE OF CONTENTS 1.0 SPECIFICATIONS ...

Waters Network Systems 2800M/MR User’s Manual Page 20 In this diagram, the subnet mask with 25-bit long, 255.2

Waters Network Systems 2800M/MR User’s Manual Page 21 According to the scheme above, a subnet mask 255.255.255.0 will pa

Waters Network Systems 2800M/MR User’s Manual Page 22 DNS: The Domain Name Server translates the human readable machine

Waters Network Systems 2800M/MR User’s Manual Page 23 Figure 5.1 – Login Screen 5.1 Overview of Web Management Once

Waters Network Systems 2800M/MR User’s Manual Page 24 Fi

Waters Network Systems 2800M/MR User’s Manual Page 25 Figure 5.3 – Port Detail Informat

Waters Network Systems 2800M/MR User’s Manual Page 26 The following list is the full function tree for web user interface

Waters Network Systems 2800M/MR User’s Manual Page 27 5.2 System Information Function name: System Information Functio

Waters Network Systems 2800M/MR User’s Manual Page 28 It is the Ethernet MAC address of the management agent in this swit

Waters Network Systems 2800M/MR User’s Manual Page 29 IP address from DHCP server, the device will stop the booting proce

Waters Network Systems 2800M/MR User’s Manual Page 3 5.16 TRUNKING CONFIGURATION ...

Waters Network Systems 2800M/MR User’s Manual Page 30 DHCP is enabled. DNS can help you easily remember the mnemonic addr

Waters Network Systems 2800M/MR User’s Manual Page 31 of hours, according to the starting date and the ending date. For e

Waters Network Systems 2800M/MR User’s Manual Page 32 Figure 5.5 – System Time Setting 5.5 Account Co

Waters Network Systems 2800M/MR User’s Manual Page 33 Figure 5.6 – Account Configuration 5.6 Management Policy Thr

Waters Network Systems 2800M/MR User’s Manual Page 34 Accept Deny Deny| Acc | Deny

Waters Network Systems 2800M/MR User’s Manual Page 35 IP Range: The switch supports two kinds of options for managed

Waters Network Systems 2800M/MR User’s Manual Page 36 The device of the group will be shown as the station address (the

Waters Network Systems 2800M/MR User’s Manual Page 37 Figure 5.9 – Virtual Stack Configuration 5.8 Port Configu

Waters Network Systems 2800M/MR User’s Manual Page 38 5.8.1 Port Status The port status function gathers the current st

Waters Network Systems 2800M/MR User’s Manual Page 39 Displays an active or inactive port. If the link is connected to a

Waters Network Systems 2800M/MR User’s Manual Page 4 1.0 Specifications OPERATIONAL CHARACTERISTICS MAC Address Table:

Waters Network Systems 2800M/MR User’s Manual Page 40 Figure 5.11 – Port Detail Parameter description of Port 25 and Po

Waters Network Systems 2800M/MR User’s Manual Page 41 Temperature: Displays the current temperature of the SFP module. V

Waters Network Systems 2800M/MR User’s Manual Page 42 Displays the fiber mode, multi or singlemode. Fiber Cable (for fibe

Waters Network Systems 2800M/MR User’s Manual Page 43 traffic can pass even if it linked up. Default: Enable. Speed/Du

Waters Network Systems 2800M/MR User’s Manual Page 44 The number of the packets received. Tx Packet: The number of the pa

Waters Network Systems 2800M/MR User’s Manual Page 45 Figure 5.15 – Detail Counter Each data field is 20-digits. If th

Waters Network Systems 2800M/MR User’s Manual Page 46 Rx Unicast Packets: Displays the number of received unicast packet

Waters Network Systems 2800M/MR User’s Manual Page 47 Packets 512-1023 Octets: Number of 512 ~ 1023-byte frames from go

Waters Network Systems 2800M/MR User’s Manual Page 48 5.9 SNMP Configuration Any Network Management System (NMS) running

Waters Network Systems 2800M/MR User’s Manual Page 49 Trap: There are six trap hosts supported. Each of them has its own

Waters Network Systems 2800M/MR User’s Manual Page 5 GVRP Port mirroring Port trunking Flow control Port security Static

Waters Network Systems 2800M/MR User’s Manual Page 50 Figure 5.17 – DHCP Boot 5.11 IGMP Snooping IGMP

Waters Network Systems 2800M/MR User’s Manual Page 51 Figure 5.18 – IGMP Snooping Configuration Function name: IGMP Sn

Waters Network Systems 2800M/MR User’s Manual Page 52 Displays VLAN ID for each multicast group. Member Port: Displays me

Waters Network Systems 2800M/MR User’s Manual Page 53 Add: A new entry of allowed group configurations can be creat

Waters Network Systems 2800M/MR User’s Manual Page 54 Symmetric VLAN: Symmetric VLAN follows an Ingress Rule (Rule 1,

Waters Network Systems 2800M/MR User’s Manual Page 55 Function description: Displays the information of existing Tag-base

Waters Network Systems 2800M/MR User’s Manual Page 56 Add Group: Input the VLAN name, VID and then choose the member by

Waters Network Systems 2800M/MR User’s Manual Page 57 Select a group entry and choose Edit to modify a group’s descriptio

Waters Network Systems 2800M/MR User’s Manual Page 58 Drop Untag: Drop untagged frame. You can configure a given port t

Waters Network Systems 2800M/MR User’s Manual Page 59 Add Group: Create a new Port-based VLAN. Input the VLAN name and c

Waters Network Systems 2800M/MR User’s Manual Page 6 OPERATING ENVIRONMENT Ambient Temperature: 32° to 104°F (0° to 40

Waters Network Systems 2800M/MR User’s Manual Page 60 Select a group entry and select Edit. This allows you to modify

Waters Network Systems 2800M/MR User’s Manual Page 61 The MAC address of the searched entry. Port: The port that exists i

Waters Network Systems 2800M/MR User’s Manual Page 62 to these two ports. This value cannot be configured. Figure

Waters Network Systems 2800M/MR User’s Manual Page 63 Figure 5.30 – Static MAC Parameter description: MAC: MAC is six-byt

Waters Network Systems 2800M/MR User’s Manual Page 64 Function name: MAC Alias Function description: MAC Alias function

Waters Network Systems 2800M/MR User’s Manual Page 65 Parameter description: MAC Address: MAC address is a six-byte lon

Waters Network Systems 2800M/MR User’s Manual Page 66 The function of GVRP Config is used to configure each port’s GVRP o

Waters Network Systems 2800M/MR User’s Manual Page 67 Disabled: In this mode, the switch dynamic VLAN will be created wh

Waters Network Systems 2800M/MR User’s Manual Page 68 JoinIn Message Packets: Number of GARP BPDU with Join In message re

Waters Network Systems 2800M/MR User’s Manual Page 69 Refresh: Refresh function allows you to see current GVRP group stat

Waters Network Systems 2800M/MR User’s Manual Page 7 2.0 Package Contents Examine the shipping container for obvious dam

Waters Network Systems 2800M/MR User’s Manual Page 70 Designated Root: Displays the root bridge ID of this network seg

Waters Network Systems 2800M/MR User’s Manual Page 71 Figure 5.35 – STP Status 5.15.2 Configuration

Waters Network Systems 2800M/MR User’s Manual Page 72 When the GSM switch is the root bridge, the whole LAN will apply th

Waters Network Systems 2800M/MR User’s Manual Page 73 5.15.3 STP Port Configuration Function name: STP Port Setting F

Waters Network Systems 2800M/MR User’s Manual Page 74 Default is 128. Admin Edge Port: If you select Yes, this port will

Waters Network Systems 2800M/MR User’s Manual Page 75 5.16 Trunking Configuration The Port Trunking Configuration is us

Waters Network Systems 2800M/MR User’s Manual Page 76 Function name: Port Setting/Status Function description: Port sett

Waters Network Systems 2800M/MR User’s Manual Page 77 Status: This field represents the trunking status of a port which

Waters Network Systems 2800M/MR User’s Manual Page 78 Figure 5.39 – Aggregator View Function name: LACP Detail (LACP Agg

Waters Network Systems 2800M/MR User’s Manual Page 79 Figure 5.40 – LACP System Priority Function name: LACP System Pr

Waters Network Systems 2800M/MR User’s Manual Page 8  Supports a snapshot of the system Information upon login  Port

Waters Network Systems 2800M/MR User’s Manual Page 80 Before the devices or workstations can access the network resource

Waters Network Systems 2800M/MR User’s Manual Page 81 Figure

Waters Network Systems 2800M/MR User’s Manual Page 82 2. Either authenticator or supplicant can initiate the message exc

Waters Network Systems 2800M/MR User’s Manual Page 83 Figure 5.43 – 802.1x Authentication The type of authe

Waters Network Systems 2800M/MR User’s Manual Page 84 Function name: 802.1X State Setting Function description: This fu

Waters Network Systems 2800M/MR User’s Manual Page 85 Indicate which port is selected to configure the 802.1X operation m

Waters Network Systems 2800M/MR User’s Manual Page 86 802.1X with Multihost mode: With the function 802.1X Port Mode Conf

Waters Network Systems 2800M/MR User’s Manual Page 87  ForceAuthorized: The controlled port remains in the authorized s

Waters Network Systems 2800M/MR User’s Manual Page 88 Figure 5.47 – Port Parameter Setting 5.18 Alarm Configuration

Waters Network Systems 2800M/MR User’s Manual Page 89 Figure 5.48 – Trap Events Configuration Function name: Email/S

Waters Network Systems 2800M/MR User’s Manual Page 9 3.5 Hardware Description Figure 3.1 - 2800M Switche

Waters Network Systems 2800M/MR User’s Manual Page 90 Mobile Phone 1-6: Additional mobile phone numbers that would like

Waters Network Systems 2800M/MR User’s Manual Page 91 Figure 5.50 – Configuration Screen

Waters Network Systems 2800M/MR User’s Manual Page 92 5.19.1 Save/Restore Function name: Save As Start Configuration Fun

Waters Network Systems 2800M/MR User’s Manual Page 93 Function name: Restore Default Configuration (inclu

Waters Network Systems 2800M/MR User’s Manual Page 94 Function name: Restore User Configuration Function description: Res

Waters Network Systems 2800M/MR User’s Manual Page 95 Figure 5.56– Restore User Configuration 5.20 Security Function

Waters Network Systems 2800M/MR User’s Manual Page 96 Figure 5.57 – Mirror Configuration Function name: Isolated Group F

Waters Network Systems 2800M/MR User’s Manual Page 97 Figure 5.58 – Isolated Group Function name: Restricted Group Func

Waters Network Systems 2800M/MR User’s Manual Page 98 Figure 5.59 – Restricted Group 5.21 Bandwidth Management Functio

Waters Network Systems 2800M/MR User’s Manual Page 99 Parameter description: Port No.: Choose the port number. Valid port